SolisStorage Energy Storage Systems: A Project-Fit Guide for Residential, Commercial, and Industrial Applications

SolisStorage Energy Storage Systems: A Project-Fit Guide for Residential, Commercial, and Industrial Applications

Selecting the right energy storage system (ESS) for a specific project is a critical procurement decision. A mismatch between system capabilities and site requirements can lead to underperformance, higher lifecycle costs, or compliance delays. SolisStorage, the energy storage subsidiary of Solis (Ginlong Technologies, Shenzhen Stock Exchange: 300763), provides a complete portfolio of ESS solutions built on more than two decades of power electronics expertise. This guide helps procurement professionals and project owners evaluate their project profile and match it with the appropriate SolisStorage system.

Defining the Problem: One Size Does Not Fit All

Energy storage projects vary widely in scale, grid interaction, environmental conditions, and operational goals. A residential system prioritises backup power and self-consumption, while a commercial & industrial (C&I) installation may require peak shaving, frequency regulation, or participation in virtual power plant (VPP) programmes. Environmental factors such as coastal salt fog, high altitude, and wide temperature ranges impose additional protection and performance requirements. Without a structured selection process, buyers risk overspending on oversized systems or choosing a unit that cannot withstand site conditions.

Industry Background: Growing Market, Growing Complexity

The global energy storage systems market was valued at approximately USD 668.7 billion in 2024 and is projected to reach USD 5.12 trillion by 2034 (Global Market Insights). The residential energy storage segment alone is estimated to grow from USD 2.69 billion in 2024 to USD 4.58 billion by 2030 (MarketsandMarkets). Long-duration energy storage (LDES) is also expanding at a CAGR of 13.6% through 2030 (MarketsandMarkets). As markets mature, buyers demand solutions that fit precise technical and commercial criteria rather than generic products.

SolisStorage Solutions: Three Product Lines for Three Application Tiers

1. IntelliHome – Residential Energy Storage System

The SolisStorage IntelliHome is a residential ESS designed for household outdoor installation. It uses a LiFePO4 battery with a nominal capacity of 5 kWh, operating voltage of 44.8–57.6 V, and a rated cell capacity of 100 Ah. Its cycle life exceeds 6,000 cycles (10 years), and it carries an IP66 ingress protection rating. The slim design and aluminium alloy casing make it suitable for wall mounting in home environments where space and aesthetics matter.

2. FlexCore-ID – Stackable Energy Storage System

The SolisStorage FlexCore-ID is a stackable ESS that targets small farms, shopping malls, hospitals, large residences, and small industrial and commercial enterprises. It uses an LFP battery cell of 314 Ah (0.5P, 25±2°C, EOL70% ≥ 8,000 cycles). The modular architecture allows capacity expansion by adding BAT20 kWh packs, making it a flexible intermediate solution between residential and full-size C&I systems.

3. EverCore ESS – C&I Energy Storage System

The SolisStorage EverCore ESS is the flagship C&I solution, available in rated energy capacities of 100.5 kWh, 120.6 kWh, and 261.2 kWh, with inverter power ratings of 50 kW, 60 kW, and 125 kW respectively. It uses 314 Ah LFP cells (EVE, 3.2 V) with an 8,000-cycle life at 0.5C. A key innovation is the AC-DC separation architecture, which physically decouples the hybrid inverter (IP66) from the battery cabinet (IP55). This design reduces heat generation inside the cabinet, raises protection ratings, and allows independent DC-side expansion (up to six cabinets per inverter). The single-unit 125 kW hybrid inverter integrates PCS, STS, PV inverter, circuit breaker protection, and EMS without external cabinets. Grid-tied/off-grid switching occurs in less than 10 ms. An ultra-simplified O&M platform saves approximately €9,500 per unit over the lifecycle by eliminating liquid cooling maintenance. The system includes 15-layer safety protection with 1,000 °C-rated insulation between packs and three-stage fire suppression. C4-grade anti-corrosion coating and operating temperature range of -25 °C to 55 °C at altitudes up to 4,000 m suit harsh outdoor and industrial environments.

Step-by-Step Project Fit Assessment

1. Define site conditions: Determine outdoor/indoor, temperature range, altitude, and corrosive exposure. If IP66/IP55 and C4 anti-corrosion are needed (e.g., coastal or industrial outdoor), the EverCore ESS meets these ratings.
2. Assess power and energy requirements: Calculate peak load and desired autonomy. For small loads under 10 kW, IntelliHome or FlexCore-ID would be considered. For 50 kW–125 kW, EverCore fits perfectly.
3. Check grid interaction: For seamless backup and VPP participation, EverCore’s sub-10 ms switching and open software ecosystem (102 third-party VPP/EMS operators across 11 European countries) enable advanced energy trading.
4. Evaluate expandability: If phased investment is planned, EverCore supports up to 6 cabinets per inverter, reducing system expansion costs by ∼10%. For medium-scale growth, FlexCore-ID offers stackable packs.
5. Review compliance: SolisStorage systems are designed to meet international standards; the EverCore carries IP66(Inverter)+ IP55(Cabinet) and C4 anti-corrosion, suitable for demanding climates.

Use Cases: Real Project Deployments

Denmark – Warehouse Self-Usage (125 kW / 261 kWh EverCore)

A C&I industrial end user installed a SolisStorage EverCore ESS at a warehouse in Denmark. The system provides self-consumption of PV power and backup. It switches between on-grid and off-grid in under 10 milliseconds to prevent interruptions. The project is expected to run for 20 years, delivering continuous electricity bill savings.

Thailand – Self-Consumption & Backup (125 kW / 522 kWh EverCore)

A project in Thailand uses two EverCore 125 kW / 261 kWh units in parallel for a total of 125 kW / 522 kWh. It serves self-consumption and backup needs for a commercial site. The system operates stably in the tropical climate, demonstrating the wide temperature tolerance and reliability of the EverCore design.

Figure: EverCore ESS in a C&I outdoor setting.

Comparison of SolisStorage Energy Storage Systems

Frequently Asked Questions

Conclusion

Choosing the right energy storage system requires a clear understanding of your project’s technical environment, power profile, expansion plans, and long-term operating costs. SolisStorage offers three distinct product lines—IntelliHome for residential, FlexCore-ID for scalable small-to-medium applications, and EverCore ESS for heavy-duty C&I use—each backed by Solis’ two decades of power electronics experience and global service network. With 8,000-cycle LFP cells, high protection ratings, and an open software ecosystem, SolisStorage systems are designed to deliver reliable, extractable value across diverse projects. For a personalised project fit analysis or to request a quote, contact SolisStorage today.

📘 Download the Solis Global Brochure (PDF)